VICTORIAHIGH-WALL DUCTLESSAIR CONDITIONING &HEATING SYSTEMINSTALLATION MANUALModels:CH09VCT115VI/CH09VCT115VOCH12VCT115VI/CH12VCT115VOCH09VCT230VI
REFRIGERANT CHARGEELECTRICAL REQUIREMENTSPIPE SIZE in (mm)Notes: Insulate both refrigerant lines, separately.Notes: 1) System must be on a single d
7Installation dimension diagram 8ft (2,4m) 6in (0,15m) 115in (3m)Space to the ceilingSpace to the obstruction 6in (0,15m)Space to the wallSpac
81. There should be no obstruction near air inlet and air outlet.2. Select a location where the condensation water can be dispersed easily and won&
9Requirements for electric connectionSafety precaution1. Must follow the electric safety regulations when installing the unit.2. According to the loca
10Installation of indoor unitStep one: choosing installation locationStep two: install wall-mounting framerm it with the client.1. Hang the wall-mount
111. Aim the pipe joint at the corresponding bellmouth.2. Pretightening the union nut with hand.3. Adjust the torque force by referring to the foll
124. Wrap the indoor pipe and joint of con- nection pipe with insulating pipe, and then wrap it with tape.Step six: install drain hoseInstallat
134.Put wiring cover back and then tighten the screw.5.Close the panel.Installation of indoor unitNote:● All wires of indoor unit and outdoor unit sho
14Installation of indoor unitStep eight: bind up pipe1. Bind up the connection pipe, power cord and drain hose with the band.indoor unitgaspipeind
Installation of outdoor unit (select it according to the actual installation situation)1. Select installation location according to th
CH09VCT115VI/CH09VCT115VO (115V)System Includes: CH09VCT115VI, CH09VCT115VOCH12VCT115VI/CH12VCT115VO (115V)System Includes: CH12VCT115VI, CH12VCT115VO
yellow-greenInstallation of outdoor unitStep four: connect indoor and outdoor pipes1. Remove the screw on the right han- dle of outdoor unit and th
17Step six: neaten the pipesOutdoor Condensate Drainage (only for Heat pump unit)1. The pipes should be placed along the wall, bent reasonably and
18(The figures in this manual may be different with the material objects, please refer to the material objects for reference)The 18K QD、24K QE UNIT dr
19Vacuum pumpingLeakage detection1. Remove the valve caps on the liquid valve and gas valve and the nut of refri- gerant charging vent.2. C
20Check after installationTest operation● Check according to the following requirement after nishing installation.Items to be checked Possible malfun
211. Standard length of connection pipe ● 16,5ft (5m), 25ft (7.5m), 26,5ft (8m).4. The additional refrigerant oil and refrigerant charging required
22Additional refrigerant charging amount for R410ADiameter of connection pipeLiquid pipe(in) Gas pipe(in)Φ1/4Φ1/4 or Φ3/8Φ3/8 or Φ1/2Φ1/2Φ5/8Φ3/4Φ7/8Φ
23Pipe expanding methodNote:Improper pipe expanding is the main cause of refrigerant leakage. Please expandthe pipe according to the following steps:A
TroubleshootingThis unit has onboard diagnostics. Error codes will appear on the LED display onthe front panel of the indoor unit in place of the temp
Cooper and Hunter © 2016For your convenience, please record the model and serial numbers of your new equipment inthe spaces provided. This information
Explanation of SymbolsIndicates a hazardous situation that, if not avoided, willresult in death or serious injury. Indicates a hazardous situation th
66160000086www.cooperandhunter.us
ContentInstallation NoticePrecautions . . ...1Sy
1PrecautionsWARNINGDo not connect air conditioner to multi-purpose socket.This appliance is not intended for use by persons (incl-Operation and Mainte
Do not block air outlet or air inlet. It may cause malfunction.remote controller may be broken.● Power cord is overheating or damaged.● There’s abnorm
Do install the circuit break. If not, it may cause malfunction. of at least 1/8in (3mm) in all poles should be connected in fixed wiring.magnet buckle
Installation must be performed in accordance with the persons in order to avoid a hazard.must be properly grounding with specialized grounding device
The indoor unit should be installed close to the wall. reachable after finishing installation.far away from animals or plants.If it is unavoidable, pl
Comments to this Manuals