Cooper&Hunter CH09ACE115V Manual and User Guide

HIGH-WALL DUCTLESSAIR CONDITIONING &HEATING SYSTEMINSTALLATION MANUALModels:CH09ACE115VI/CH09ACE115VO (115V) CH12ACE115VI/CH12ACE115VO (115V)CH09A

REFRIGERANT CHARGEELECTRICAL REQUIREMENTSPIPE SIZE in (mm)Notes: Insulate both refrigerant lines, separately.Notes: 1) System must be on a single d

7Installation dimension diagram 8ft (2,4m) 6in (0,15m) 20in (0,5m)12in(0,3m) 115in (3m) 80in (2,03m)Space to the obstructionSpace to the obst

81. There should be no obstruction near air inlet and air outlet.2. Select a location where the condensat- ion water can be dispersed easily and

9Requirements for electric connectionSafety precautionGrounding requirement1. Must follow the electric safety regulations when installing the unit.

10Installation of indoor unitStep one: choosing installation locationrm it with the client.1. Choose the position of piping hole according to the dire

111. Aim the pipe joint at the corresponding bellmouth.2. Pretightening the union nut with hand.3. Adjust the torque force by referring to the foll

124. Wrap the indoor pipe and joint of con- nection pipe with insulating pipe, and then wrap it with tape.Step six: install drain hoseInstallat

134. Put wiring cover back and then tighten the screw.5. Close the panel.Installation of indoor unitNote:● All wires of indoor unit and outdoor unit s

14Installation of indoor unitStep eight: bind up pipe1. Bind up the connection pipe, power cord and drain hose with the band.indoor unitgaspipeind

15Installation of outdoor unit (select it according to the actual installation situation)1. Select installation location according to

CH09ACE115VI/CH09ACE115VOSystem Includes: CH09ACE115VI, CH09ACE115VOCH12ACE115VI/CH12ACE115VOSystem Includes: CH12ACE115VI, CH12ACE115VOCH09ACE230VI/C

16Installation of outdoor unitStep four: connect indoor and outdoor pipes1. Remove the screw on the right handle of outdoor unit and then remove t

17Installation of outdoor unit1. Remove the wire clip; connect the power connection wire and signal control wire (only for cooling and heating uni

18● The through-wal height of drain hose shouldn't be higher than the outlet pipe hole of indoor unit.● Slant the drain hose slightly dow-

19Leakage detection sure of piezometer remains in -0.1MPa. If the pressure decreases, there may be leakage.5. Remove the piezometer, open the v

20Check after installationTest operation● Check according to the following requirement after nishing installation.Items to be checked Possible malfun

21Conguration of connection pipe4. The additional refrigerant oil and refrigerant charging required after prolonging connection pipe ● After

22Additional refrigerant charging amount for R410AConguration of connection pipeDiameter of connection pipeLiquid pipe(in) Gas pipe(in)Φ1/4Φ1/4 or Φ3

23Pipe expanding methodNote:Improper pipe expanding is the main cause of refrigerant leakage. Please expandthe pipe according to the following steps:A

TroubleshootingThis unit has onboard diagnostics. Error codes will appear on the LED display onthe front panel of the indoor unit in place of the temp

Cooper and Hunter © 2016For your convenience, please record the model and serial numbers of your new equipment inthe spaces provided. This information

ContentInstallation NoticePrecautions ...1Sys

66162927www.cooperandhunter.us

Explanation of SymbolsIndicates a hazardous situation that, if not avoided, willresult in death or serious injury. Indicates a hazardous situation th

PrecautionsWARNINGDo not connect air conditioner to multi-purpose socket.This appliance can be used by children aged from 8 Operation and MaintenanceI

Do not block air outlet or air inlet. It may cause malfunction.remote controller may be broken.● Power cord is overheating or damaged.● There’s abnorm

Do install the circuit break. If not, it may cause malfunction. of at least 1/8in (3mm) in all poles should be connected in fixed wiring.magnet buckle

Installation must be performed in accordance with the persons in order to avoid a hazard.must be properly grounding with specialized grounding device

The indoor unit should be installed close to the wall. Instructions for installation and use of this product are provided by the manufacturer.Precauti